A soundboard (also known as a 'Mixing Board', 'Mix Console' or 'Sound Desk') is a complex and sometimes intimidating piece of equipment. Here is a very basic guide to setting up a mixing board for a small live show with a basic bare bones PA system setup. Before we get to the step-by-step portion it is necessary to understand the basic layout of a sound board.
A mixing board has two main sections: the input section and the output or master section. The input section is made up of a number of separate channels, there can be anywhere from four channels on a mixing board to upwards of thirty-two.
Each channel consists of a set of inputs, on the back of the board and a corresponding set of controls which together are called a channel strip. Chose a location for your sound board. This is important because sound volume decreases as you get further away from the source of the sound and the way that sound reflects off surfaces in the room; you want to be in a place where you are far enough away from the speakers that you don't have sound blasting directly in your face all night, but close enough that you don't end up turning the mix up way too loud because you can't hear it at the back of the room.
You will also need to consider the length of your mic cables and the location of the electrical outlets in the room.
If your computer has external speakers, make sure that they are turned on and that the volume is turned up. Make sure that the speaker cable is securely plugged into the “output” audio socket on your computer. This socket is usually light green in color. Some sound cards can switch between the socket they use for output (to the speakers) and the socket for input (from a microphone, for instance). The output socket may be different when running Linux, Windows or Mac OS. Try connecting the speaker cable to a different audio socket on your computer. A final thing to check is that the audio cable is securely plugged into the back of the speakers.
Some speakers have more than one input, too. Go to the Activities overview and open a Terminal. Run lspci as; either type sudo lspci and type your password, or type su, enter the root (administrative) password, then type lspci. Check if an audio controller or audio device is listed: in such case you should see the make and model number of the sound card. Also, lspci -v shows a list with more detailed information. You may be able to find and install drivers for your card.
It is best to ask on support forums (or otherwise) for your Linux distribution for instructions. If you cannot get drivers for your sound card, you might prefer to buy a new sound card. You can get sound cards that can be installed inside the computer and external USB sound cards.
Download free font noteworthy. A soundboard (also known as a 'Mixing Board', 'Mix Console' or 'Sound Desk') is a complex and sometimes intimidating piece of equipment. Here is a very basic guide to setting up a mixing board for a small live show with a basic bare bones PA system setup.
Before we get to the step-by-step portion it is necessary to understand the basic layout of a sound board. A mixing board has two main sections: the input section and the output or master section. The input section is made up of a number of separate channels, there can be anywhere from four channels on a mixing board to upwards of thirty-two. Each channel consists of a set of inputs, on the back of the board and a corresponding set of controls which together are called a channel strip. Chose a location for your sound board.
This is important because sound volume decreases as you get further away from the source of the sound and the way that sound reflects off surfaces in the room; you want to be in a place where you are far enough away from the speakers that you don't have sound blasting directly in your face all night, but close enough that you don't end up turning the mix up way too loud because you can't hear it at the back of the room. You will also need to consider the length of your mic cables and the location of the electrical outlets in the room.
Tabletop Game Soundboard
Quote: Almost went crazy trying to fix this, im going to guess u also have realtek audio driver, if so just go to manager, Digital Input, and mute the recording Volume, if not, try finding a similar option. Another option that was mentioned was to disable all of the other sound input/output devices besides your headset. it seems that this is quite a common occurance. I'm not sure if its a skype issue or windows issue to be honest. Or perhaps it is just poor audio drivers.
What drivers do you have? Killzone2367 said: I had this problem last year when I first installed Windows 8. I just reinstalled Windows because of another issue, and now this sound issue is back. I dont really remember what I did to fix it back then. Yes I have an onboard realtek card. This is the driver I installed: I am having this exact same issue. Windows 8.1 - realtek audio onboard gigabyte z77 mobo i have messed around with any and all settings i could.
I have isolated the issue to windows tho by recording me talking, then playing music on youtube, and i play it back and the music is recorded as well. Getting annoying for online gaming applications. Literally cannot use voice chat at this point. Killzone2367 said: Thanks for the reply! No, I'm using a Razer Kraken Pro headset. It's not sound bleeding from the headset. I would purposely trigger Windows system sounds on Skype, and people can hear them clearly as if it was their PC making the noise.
Goodbye
Also Steam notifications would be transmitted clearly. From what i understand its an issue with the kraken pro itself that seems quite common. Two ways which you can attempt to fix it are: 1. Mess with your mic levels in control panel- manage audio devices- recording - properties- levels 2. Buy a 3.5mm to usb sound card and wire your kraken pro through that i have tried the first one and while it works it also makes your mic very quiet, looking at picking up a usb sound card soonish.